Please install the Hard Disk first. If not, the Video Recorder can only monitor normally, but it can not record or playback.
Notice: Please try to choose a special monitoring hard drive disk in order to record for a longer time. The video recorder supports 3.5″ or 2.5″ SATA Hard Drive Warning: please make sure the power is off before installation.
Make sure the power supply matches the requirements of the hard disk video recorder.
After connecting the power, the indicator on the front of the NVR will light on and you will hear a buzzer sound, then the display will boot up and the device will access to the preview image.
After the recovery of the non-normal power failure, the device will be automatically restored to the state before the power is off.
After the normal boot, you have to log in first and the system will provide the corresponding function according to the user’s rights. Right click the mouse – (Main Menu) Default username: admin
Password:(leave it blank, null password)
Right click the mouse >【Main Menu】>【Advanced】>【HDD info】 Choose the Hard Disk, click Format Storage, start to format the HDD. Notice: Please confirm the Hard Disk is connected. The hard disk should be formatted before first use, so that it can record. It will be automatically overwritten when the Hard Disk storage is ful I if you set overwrite.
Right click the mouse > 【Main Menu】>【System】>【General】
[Storage Full] Choose Overwrite: continue recording video and cycle covering the former video while the storage of HDD is full. Choose Stop: Stop recording video while the storage of HDD is full. [Auto Logout] You can set up a 0-60 min auto standby, 0 min means you don’t set up the standby time. [Startup Wizard] Tick it to get startup wizard when reboot the system. (untick it as default)
Right click the mouse >【Main Menu】 >【Record Conf.】
[Length] Set up the time length for per Video file, Default time is 60 minutes. [Period] Set up the record period, it will start-up recording within the period. [Regular] Within the setup period, regular recording video. [Detect] Within the setup period, trigger “motion” signal, the device start to record motion. Notice: Default setting is a 24-hour recording continuously for all channels.
Right click the mouse >【Main Menu】>【PlayBack】
Right click the mouse > 【Main Menu】> 【System】> 【Backup】
Choose Video Type > Choose Channel > Choose time > Click Add button, search Video file, Choose the file in the list, Click Start button to backup, it will automatically prompt after backup completed.
Notice: USB disk must be FAT32 format. Please choose AVI format while backup, so that the backup video could play on PC directly.
Right click the mouse >【Main Menu】>【Alarm】>【IntelI igent Alert】
[Channel] Select demand Channel.
[IPC Activation] Set Alarm Sound and voice Prompts.
[Human Detect] When it detects people, it starts to record motion.
[Rule] Set detect area rule.
[Period] During the setting period, the device will trigger the alarm signal of human detection.
[Record Channel] Current channel you are setting is the Default Record Channel, when current channel detects motion, other channel will record motion if you choose other channels.
[MD Interval] During the interval time, there will trigger one alarm signal though is has motion detection for several times.
[Show Message] Tick it to show Alarm Status when detect motion.
[Buzzer] Tick it to beep when detect motion.
[FTP upload] Tick it to send message to FTP when detect motion.
[Send Email] Tick it to send Email when detect motion.
[Write Log] Tick it to write log when detect motion.
[Mobile reported] Tick it to send notifications to mobile via APP when detect motion.
Connect NVR to Router > Right click the mouse >【Main Menu】>【 Network】
[DHCP Enable] Tick it to automatically obtain the IP address assigned by the server.
[IP address] Must be a unique IP address on the same LAN segment to avoid conflicts with other equipment in local area.
[HTTP Port] a port number for remote visit, default value is 80.
Right click the mouse >【Main Menu】>【Advanced】>【Version】
[Series Number] Device Serial Number for remote view.
[Nat Status] Check the network status, begin a remote monitoring when shows connected.
Right click the mouse>【Main Menu】>【Network】> 【NetService】>【Email】
[SMTP Server] Sender’s mailbox (for example: gmail email).
[Port] Sender’s mailbox SMTP port.
[Encryption] SSL
[User Name] Username of the sender’s mailbox (must support and open SMTP function).
[Password] Password of the sender’s mailbox.
[Receiver] Receiver’s mailbox.
Click [Mail Testing] Send an email to receiver to test the Email setting.
Notice: Before testing the Email, please confirm the Network has been connected successfully. If it failed, then change Encryption to TLS or NONE.
Right click screen >【Main Menu】>【System】>【Account】
[Modify Password] Enter to Modify Password page, and modify password.
[Add User] Add User account and setup the User’s permissions. Enter into the Add User page, input the User Name and Password.
Notice: Password can be setup as number+letter combination, please record your password in other ways and keep it in a safe place to avoid forgetting.
Right click the mouse >【Main Menu】>【System】>【Encode】
[Video/Audio] Four ✓ show the video file for streaming video and audio
